Design Addict

Cart

Can anyone identify...
 

Can anyone identify this wall unit?  

Page 1 / 2
  RSS

McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 10:47 pm  

I found this wonderful wall unit but there is a major drawback. None of the hardware comes with it. The unit has no maker's mark either. I have seen the drawer pulls before but I cannot remember where I have seen them. Any ideas are appreciated! I'd love to be able to track down the hardware so any suggestions about that would also be appreciated!

I put a pic on flickr. If you see it, note one piece in the right lower corner is not part of the system.

Thanks!

http://www.flickr.com/photos/42891622@N03/3954006702/


Quote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 10:56 pm  

PS Systems
Denmark, as far as I can see..
Has it got U shaped clips behind?
These usually hang on verticals with horizontal dowels threaded through


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 10:57 pm  

Yes
Yes, they do have the u shaped hook and there was one lone rod that comes with it....
Thanks for your help.


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 10:58 pm  

Looking at the photos again
you have the uprights, you just need round metal dowels to fit through the holes in the uprights!
You checked all the drawers and cupboards to see if they're there somewhere ?


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 10:59 pm  

any ideas on hardware?
Just wondering if you have any ideas about tracking down hardware.....


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 11:00 pm  

how to keep the shelves up?
I can make some rods for the units but the shelves need some kind of wire to support them.


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 11:06 pm  

Yes
they need an angled steel rod with opposing turns at each end..if that makes sense ?


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 11:10 pm  

Hmmmnnn
The shelves appear to have holes in them as if the rod is supposed to go through it.


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 11:11 pm  

PS Systems
It is tough finding anything on PS Systems. Any idea where I could look?


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 11:14 pm  

This
is a Cado one, the PS ones have the same as the end of left hand side, but on opposing sides.
I'm sure they could be easily made by a metal worker if you can work out the dimensions needed
I'd do it for you- but don't have any PS anymore


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 11:17 pm  

Few things on
Google
http://tinyurl.com/ygfbqw7


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 11:18 pm  

Thank you
I can buy this set as is for $750.00 US. Do you think it's worth it considering I'll have to have hardware made for it? It's in like new condition and huge....
And thanks for posting the pic.


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 11:20 pm  

Just remembered
some of the PS shelves I've had had a thread and a nut at one end that goes under the shelf to hold it.
a little bit more complicated to make, but not beyond the average metalworker


ReplyQuote
Robert Leach
(@robertleach1960yahoo-co-uk)
Illustrious Member
Joined: 6 years ago
Posts: 3212
16/11/2009 11:23 pm  

I
have little idea on the US retail scene or how much the components would cost to manufacture, being from the UK.
Maybe someone from the US could help you better- there are some pretty well-informed people here


ReplyQuote
McGarrett
(@mcgarrett)
Active Member
Joined: 15 years ago
Posts: 18
16/11/2009 11:29 pm  

shelves
Yes, I think these shelves had a screw-type piece on the bottom. As for the cost, it was shot in the dark. I really like it so I may just roll the dice.
Thanks again for all your help!


ReplyQuote
Page 1 / 2
Share:

If you need any help, please contact us at – info@designaddict.com

  
Working

Please Login or Register